Difference between revisions of "Select a waypoint from the database"

From Air Navigation User Manuals
Jump to navigation Jump to search
(8 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
<languages />
 
<languages />
 
<translate>
 
<translate>
<!--T:3-->
 
 
<br />
 
<br />
 
----
 
----
Line 7: Line 6:
 
__TOC__
 
__TOC__
 
<br />
 
<br />
==Quick Search==
+
==Quick Search== <!--T:3-->
The Quick Search will allow you to not only get quickly to a desired waypoint, but also to create new ones by using certain commands. The results can be selected as direct-to destinations, added to the current route, shown on map or added as an user waypoint (if it isn't already a waypoint on the database).
+
The Quick Search will allow you to not only get quickly to a desired waypoint, but also to create new ones by using certain commands. The results can be selected as direct-to destinations, added to the current route, shown on map or added as an user waypoint (if it isn't already a waypoint in the database).
===Search by Identifier===
+
 
 +
<!--T:43-->
 +
[[File:6854198.jpg|300px]]
 +
 
 +
===Search by Identifier=== <!--T:44-->
 
By entering at least 3 characters in the search field the search engine will start searching in the database. It will look after:
 
By entering at least 3 characters in the search field the search engine will start searching in the database. It will look after:
 
* IDs (ICAO Codes or Navaids IDs) in the waypoints database (Custom user waypoints incl.)
 
* IDs (ICAO Codes or Navaids IDs) in the waypoints database (Custom user waypoints incl.)
Line 17: Line 20:
 
The results will be displayed under categories (Waypoints, Radionavigation Beacons, Airports).
 
The results will be displayed under categories (Waypoints, Radionavigation Beacons, Airports).
  
===Search Coordinates===
+
===Search Coordinates=== <!--T:5-->
 
You can also enter coordinates in the following formats / grids / datums:
 
You can also enter coordinates in the following formats / grids / datums:
 
{|
 
{|
 
|
 
|
*WGS84 in DD:MM:SS
+
* WGS84 in DD:MM:SS
 
* WGS84 in DD:MM.decimal
 
* WGS84 in DD:MM.decimal
 
* WGS84 in DD.decimal
 
* WGS84 in DD.decimal
Line 42: Line 45:
 
|}
 
|}
  
 +
<!--T:6-->
 
The engine will try to interpret the input to match the correct datum. In order to avoid ambiguity between grids it is necessary to enter the 2-letter code of the target country:
 
The engine will try to interpret the input to match the correct datum. In order to avoid ambiguity between grids it is necessary to enter the 2-letter code of the target country:
  
 +
<!--T:7-->
 
Irish grids : IE <br />
 
Irish grids : IE <br />
 
New Zealand grids : NZ <br />
 
New Zealand grids : NZ <br />
Line 50: Line 55:
 
Swedish grids : SE <br />
 
Swedish grids : SE <br />
  
====Examples====
+
====Examples==== <!--T:8-->
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
Line 69: Line 74:
 
|}
 
|}
  
 +
<!--T:9-->
 
If a valid coordinate has been entered the result will appear as the first line of the search result. A true bearing and distance from the current GPS location will be displayed as well.
 
If a valid coordinate has been entered the result will appear as the first line of the search result. A true bearing and distance from the current GPS location will be displayed as well.
  
===Searching relative waypoints===
+
===Searching relative waypoints=== <!--T:10-->
 
By using similar syntax as when looking for coordinates and adding commands, it is possible to create waypoints relative to a known location. 3 Modes are available:
 
By using similar syntax as when looking for coordinates and adding commands, it is possible to create waypoints relative to a known location. 3 Modes are available:
 
* Location, Direction, Distance
 
* Location, Direction, Distance
 
* Location, Direction, Speed, Time
 
* Location, Direction, Speed, Time
 
* Location, Direction, Location, Direction
 
* Location, Direction, Location, Direction
 
+
<br />
 
'''Location''': can be either a coordinate or a waypoint identifier
 
'''Location''': can be either a coordinate or a waypoint identifier
  
 +
<!--T:11-->
 
'''Direction''': can be true bearing or radial.
 
'''Direction''': can be true bearing or radial.
 
* True bearing will be an angle from 0 to 360 and prefixed with a B, e.g. B055.
 
* True bearing will be an angle from 0 to 360 and prefixed with a B, e.g. B055.
 
* Radial will be treated as a magnetic bearing and will be an angle from 0 to 360, prefixed with a R, e.g. R220. It will be converted to true by using the current magnetic variation model.
 
* Radial will be treated as a magnetic bearing and will be an angle from 0 to 360, prefixed with a R, e.g. R220. It will be converted to true by using the current magnetic variation model.
 
+
<br />
 
'''Distance''': a value in nautical miles prefixed with a D. An optional suffix will allow using other units. Example: D120KM.
 
'''Distance''': a value in nautical miles prefixed with a D. An optional suffix will allow using other units. Example: D120KM.
 
Supported units:
 
Supported units:
Line 88: Line 95:
 
* KM (Kilometers)
 
* KM (Kilometers)
 
* M (meters)
 
* M (meters)
 
+
<br />
 
'''Speed''': a value in knots prefixed with a S or GS. An optional suffix will allow using other units. Example: S100KMH.
 
'''Speed''': a value in knots prefixed with a S or GS. An optional suffix will allow using other units. Example: S100KMH.
 
Supported units:
 
Supported units:
Line 94: Line 101:
 
* KMH (kilometer per hour)
 
* KMH (kilometer per hour)
 
* MPS (meters per second)
 
* MPS (meters per second)
 
+
<br />
 
'''Time''': can be a relative in minutes or an absolute time in HH:MM UTC, prefixed with T or AT for absolute. Example: AT08:21.
 
'''Time''': can be a relative in minutes or an absolute time in HH:MM UTC, prefixed with T or AT for absolute. Example: AT08:21.
  
====Examples====
+
====Examples==== <!--T:12-->
 
=====Location, Direction, Distance=====
 
=====Location, Direction, Distance=====
 
For these examples we will use the WGS84 in DD:MM:SS format DD:MM:S
 
For these examples we will use the WGS84 in DD:MM:SS format DD:MM:S
  
 +
<!--T:13-->
 
Creating a waypoint knowing a radial and DME to a navigation aid
 
Creating a waypoint knowing a radial and DME to a navigation aid
 
For this we need to enter a string with the following information: Location of the navigation aid (ICAO Code or Coordinates), radial and distance to the aid (in Nautical miles, Statute miles, Kilometers or meters)
 
For this we need to enter a string with the following information: Location of the navigation aid (ICAO Code or Coordinates), radial and distance to the aid (in Nautical miles, Statute miles, Kilometers or meters)
  
 +
<!--T:14-->
 
Let's say I want to create a point that is on radial 275 of the VOR of Geneva (GVA) at 25NM DME
 
Let's say I want to create a point that is on radial 275 of the VOR of Geneva (GVA) at 25NM DME
 
I will have to enter the following string in the tool:
 
I will have to enter the following string in the tool:
 
'''GVA, R275, D25'''  
 
'''GVA, R275, D25'''  
  
 +
<!--T:15-->
 
The tool will choose the navigation aid with that name that is nearest to your actual position. Alternatively you can enter the coordinates:  
 
The tool will choose the navigation aid with that name that is nearest to your actual position. Alternatively you can enter the coordinates:  
  
 +
<!--T:16-->
 
'''46:15:12 N 06:08:14 E, R275, D25'''
 
'''46:15:12 N 06:08:14 E, R275, D25'''
  
 +
<!--T:17-->
 
If you want to use the true bearing instead of the radial you have to change the R for a B. An to change the unit just add SM for statute mile, KM for Kilometer or M for meter at the end of Distance:
 
If you want to use the true bearing instead of the radial you have to change the R for a B. An to change the unit just add SM for statute mile, KM for Kilometer or M for meter at the end of Distance:
  
 +
<!--T:18-->
 
'''GVA, B275, D25KM'''
 
'''GVA, B275, D25KM'''
  
=====Location, Direction, Speed, Time=====
+
=====Location, Direction, Speed, Time===== <!--T:19-->
 
Let 's say you are flying and you are requested by ATC to report your position 5 minutes after passing over GVA. You are flying at 108 knots GS and you are on the radial 275 of GVA.
 
Let 's say you are flying and you are requested by ATC to report your position 5 minutes after passing over GVA. You are flying at 108 knots GS and you are on the radial 275 of GVA.
  
 +
<!--T:20-->
 
You can enter this String and the tool will search for that point:
 
You can enter this String and the tool will search for that point:
 
GVA, R275, S108, T5
 
GVA, R275, S108, T5
  
 +
<!--T:21-->
 
You can also enter a specific time in UTC. Use the Code AT before the time for this:
 
You can also enter a specific time in UTC. Use the Code AT before the time for this:
 
GVA, R275, S108, AT12:58
 
GVA, R275, S108, AT12:58
  
 +
<!--T:22-->
 
You can also enter the speed in statute miles per hour, kilometers per hour and meters per second. Enter just MPH, KMH or MPS after the speed.
 
You can also enter the speed in statute miles per hour, kilometers per hour and meters per second. Enter just MPH, KMH or MPS after the speed.
  
=====Location, Direction, Location, Direction=====
+
=====Location, Direction, Location, Direction===== <!--T:23-->
 
Creating a waypoint knowing the radials of two navigation aids
 
Creating a waypoint knowing the radials of two navigation aids
 
You can create a point easily by entering the following information: Navigation Aid 1, Radial 1, Navigation Aid 2, Radial 2.
 
You can create a point easily by entering the following information: Navigation Aid 1, Radial 1, Navigation Aid 2, Radial 2.
  
 +
<!--T:24-->
 
GVA, R100 , SCS, R300
 
GVA, R100 , SCS, R300
  
 +
<!--T:45-->
 
Of course you can use coordinates or bearings for the above command.
 
Of course you can use coordinates or bearings for the above command.
 +
 +
<!--T:46-->
 +
[[File:98146.jpg]]
 +
 +
 +
===Search by geocoded places=== <!--T:47-->
 +
[[File:geocode.jpg|250px|caption|left]]It is also possible to search by place names. By acquiring our Add-on '''Streets and places search''' you will be able to search for places like hotels, bars, hospitals and much more points of interest in the database. You can then use these points as regular waypoints by adding them to routes or showing them on the map.
 +
 +
 +
 +
 +
 +
 +
 +
 
----
 
----
==Browse Database==
+
==Browse Database== <!--T:25-->
[[File:searchimage.jpg|thumb]]If you are not able to find the waypoint you are looking for, you can tap on "browse databade...". You can visualize quickly nearby waypoints or use the «search» tab to go search by country or search directly the waypoint you are looking for. It is possible to search by “name”, “ID” or “place”.
+
[[File:searchimage.jpg|right|caption|300px]]If you are not able to find the waypoint you are looking for, you can tap on "browse databade...". You can visualize quickly nearby waypoints or use the «search» tab to go search by country or search directly the waypoint you are looking for. It is possible to search by “name”, “ID” or “place”.
 
Once you found the desired waypoint, you can directly press on it
 
Once you found the desired waypoint, you can directly press on it
 
to select it as a “direct to” or adjust it to one of the instruments (HSI, VOR, ADF); or you can press on the blue disclosure button on the right side and check the information about it such as name, city, frequency (for Navaids), runway and contact frequency info (for Airfields) and you can center the waypoint  on the moving map by selecting «Show on map» button.
 
to select it as a “direct to” or adjust it to one of the instruments (HSI, VOR, ADF); or you can press on the blue disclosure button on the right side and check the information about it such as name, city, frequency (for Navaids), runway and contact frequency info (for Airfields) and you can center the waypoint  on the moving map by selecting «Show on map» button.
  
<!--T:4-->
 
 
[[File:showonmap.jpg]]
 
[[File:showonmap.jpg]]
 
----
 
----
==Create Waypoint via URL==
+
==Create Waypoint via URL== <!--T:4-->
 
In order to help the workflow it is possible to quickly insert waypoints in the application by tapping on a specially formatted URL. The URL can be sent by E-Mail, SMS or browsed on a website.
 
In order to help the workflow it is possible to quickly insert waypoints in the application by tapping on a specially formatted URL. The URL can be sent by E-Mail, SMS or browsed on a website.
  
 +
<!--T:26-->
 
Supported actions:
 
Supported actions:
 
* Direct-to
 
* Direct-to
Line 151: Line 184:
 
* Create route
 
* Create route
  
 +
<!--T:27-->
 
The URL looks something like this:
 
The URL looks something like this:
 
Clean: airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field
 
Clean: airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field
 
Encoded query: airnavpro://direct-to?coordinates%3Dwgs84-decimal%26location%3D46.875_7.234%2C0.0%2CWP1%2CGrass%20field
 
Encoded query: airnavpro://direct-to?coordinates%3Dwgs84-decimal%26location%3D46.875_7.234%2C0.0%2CWP1%2CGrass%20field
  
 +
<!--T:28-->
 
It consists of:
 
It consists of:
 
* URL scheme: airnavpro://
 
* URL scheme: airnavpro://
Line 160: Line 195:
 
* Coordinates format: coordinates=wgs84-decimal
 
* Coordinates format: coordinates=wgs84-decimal
 
* waypoint(s): location=46.875_7.234,0.0,WP1,Grass field
 
* waypoint(s): location=46.875_7.234,0.0,WP1,Grass field
 
+
<br />
Note: The query part of the URL has to be URL encoded in order to support special characters.
+
----
 
+
<u>'''Note:'''</u> The query part of the URL has to be URL encoded in order to support special characters.
 +
----
 +
<br />
 
Coordinates formats:
 
Coordinates formats:
 
{|
 
{|
Line 187: Line 224:
 
|}
 
|}
  
 +
<!--T:29-->
 
Waypoint format
 
Waypoint format
 
For any action the waypoint can be defined with different values separated by a comma (,). Waypoints are separated by semicolons (;).
 
For any action the waypoint can be defined with different values separated by a comma (,). Waypoints are separated by semicolons (;).
  
 +
<!--T:30-->
 
Waypoint values:
 
Waypoint values:
 
# Coordinates
 
# Coordinates
Line 195: Line 234:
 
# Waypoint ID
 
# Waypoint ID
 
# Waypoint name
 
# Waypoint name
 
+
<br />
 
A waypoint must at least contain the coordinates information. The coordinates information may be composed of two values, in this case the coordinates must be linked with a underscore (_). For example, a waypoint description for a wgs84 decimal format: 46.875_7.234
 
A waypoint must at least contain the coordinates information. The coordinates information may be composed of two values, in this case the coordinates must be linked with a underscore (_). For example, a waypoint description for a wgs84 decimal format: 46.875_7.234
  
 +
<!--T:31-->
 
Here is a full example with elevation, ID and name data: 46.875_7.234,0.0,WP1, Antenna
 
Here is a full example with elevation, ID and name data: 46.875_7.234,0.0,WP1, Antenna
  
===Direct-to===
+
===Direct-to=== <!--T:32-->
 
Direct to can be achieved by formatting an URL with the "direct-to" command. Only one waypoint can be specified and it has to be in the form like :
 
Direct to can be achieved by formatting an URL with the "direct-to" command. Only one waypoint can be specified and it has to be in the form like :
  
 +
<!--T:33-->
 
location=waypoint
 
location=waypoint
  
 +
<!--T:34-->
 
Here are some examples of direct-to URLs :
 
Here are some examples of direct-to URLs :
  
 +
<!--T:35-->
 
WGS84 decimal
 
WGS84 decimal
 
   - airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field
 
   - airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field
  
 +
<!--T:36-->
 
WGS84 degrees minutes seconds
 
WGS84 degrees minutes seconds
 
   - airnavpro://direct-to?coordinates=wgs84-ddmmss&location=N 12°34′56′′_W 78°12′34′′,0.0,WP1,Grass field
 
   - airnavpro://direct-to?coordinates=wgs84-ddmmss&location=N 12°34′56′′_W 78°12′34′′,0.0,WP1,Grass field
  
 +
<!--T:37-->
 
Swissgrid CH1903
 
Swissgrid CH1903
 
   - airnavpro://direct-to?coordinates=swiss&location=602030.68_191775.03,0.0,WP1,Zimmerwald
 
   - airnavpro://direct-to?coordinates=swiss&location=602030.68_191775.03,0.0,WP1,Zimmerwald
  
===Import waypoints to user database===
+
===Import waypoints to user database=== <!--T:38-->
 
A list of waypoints can be imported directly in the user database with a specially formatted URL with the "add-waypoints" command. A list of waypoints can be specified and it has to be in the form like :
 
A list of waypoints can be imported directly in the user database with a specially formatted URL with the "add-waypoints" command. A list of waypoints can be specified and it has to be in the form like :
  
 +
<!--T:39-->
 
waypoints=point1;point2;point3
 
waypoints=point1;point2;point3
  
 +
<!--T:40-->
 
Here is an example of add-waypoints URLs :
 
Here is an example of add-waypoints URLs :
 
   - airnavpro://add-waypoints?coordinates=wgs84-decimal&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna
 
   - airnavpro://add-waypoints?coordinates=wgs84-decimal&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna
  
===Create Route===
+
===Create Route=== <!--T:41-->
 
A new route with a list of waypoints can be created and loaded directly with a specially formatted URL with the "new-route" command. A route name and list of waypoints can be specified and it has to have a form like:
 
A new route with a list of waypoints can be created and loaded directly with a specially formatted URL with the "new-route" command. A route name and list of waypoints can be specified and it has to have a form like:
 
route-name=myRoute&waypoints=point1;point2;point3
 
route-name=myRoute&waypoints=point1;point2;point3
  
 +
<!--T:42-->
 
Here is an example of add-waypoints URLs :
 
Here is an example of add-waypoints URLs :
 
   - airnavpro://new-route?coordinates=wgs84-decimal&route-name=myRoute&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna
 
   - airnavpro://new-route?coordinates=wgs84-decimal&route-name=myRoute&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna

Revision as of 15:33, 12 January 2016

Other languages:
English • ‎español • ‎français



Wpimage.jpgBy pressing on this button at the top toolbar on an iPad or within the toolbar in an iPhone/iPod Touch (accessible from the «screwdriver» button), you can have access to the waypoints database.


Quick Search

The Quick Search will allow you to not only get quickly to a desired waypoint, but also to create new ones by using certain commands. The results can be selected as direct-to destinations, added to the current route, shown on map or added as an user waypoint (if it isn't already a waypoint in the database).

6854198.jpg

Search by Identifier

By entering at least 3 characters in the search field the search engine will start searching in the database. It will look after:

  • IDs (ICAO Codes or Navaids IDs) in the waypoints database (Custom user waypoints incl.)
  • Name of cities or mountains
  • Documents stored in the document browser


The results will be displayed under categories (Waypoints, Radionavigation Beacons, Airports).

Search Coordinates

You can also enter coordinates in the following formats / grids / datums:

  • WGS84 in DD:MM:SS
  • WGS84 in DD:MM.decimal
  • WGS84 in DD.decimal
  • Standard UTM
  • UTM with bands
  • UPS
  • MGRS 100m
  • MGRS 10m
  • MGRS 1m
  • Irish grid without zone
  • Irish grid with zone
  • NZ Grid 1949
  • NZ Grid 2000
  • Swissgrid (CH1903)
  • UK Grid without zone
  • UK Grid with zone
  • Swedish grid RT90
  • Swedish grid SWERED99TM

The engine will try to interpret the input to match the correct datum. In order to avoid ambiguity between grids it is necessary to enter the 2-letter code of the target country:

Irish grids : IE
New Zealand grids : NZ
Swiss grid : CH
UK grids : UK
Swedish grids : SE

Examples

WGS84 in DD.decimal 46.8943 -5.4535
WGS84 in DD:MM:SS 23:34:56N 145:12:01W
Swissgrid CH 553986 200005
Swedish grid SE 6669189 486557
MGRS 32TKR6770698424

If a valid coordinate has been entered the result will appear as the first line of the search result. A true bearing and distance from the current GPS location will be displayed as well.

Searching relative waypoints

By using similar syntax as when looking for coordinates and adding commands, it is possible to create waypoints relative to a known location. 3 Modes are available:

  • Location, Direction, Distance
  • Location, Direction, Speed, Time
  • Location, Direction, Location, Direction


Location: can be either a coordinate or a waypoint identifier

Direction: can be true bearing or radial.

  • True bearing will be an angle from 0 to 360 and prefixed with a B, e.g. B055.
  • Radial will be treated as a magnetic bearing and will be an angle from 0 to 360, prefixed with a R, e.g. R220. It will be converted to true by using the current magnetic variation model.


Distance: a value in nautical miles prefixed with a D. An optional suffix will allow using other units. Example: D120KM. Supported units:

  • SM (Statute miles)
  • KM (Kilometers)
  • M (meters)


Speed: a value in knots prefixed with a S or GS. An optional suffix will allow using other units. Example: S100KMH. Supported units:

  • MPH (statue miles per hour)
  • KMH (kilometer per hour)
  • MPS (meters per second)


Time: can be a relative in minutes or an absolute time in HH:MM UTC, prefixed with T or AT for absolute. Example: AT08:21.

Examples

Location, Direction, Distance

For these examples we will use the WGS84 in DD:MM:SS format DD:MM:S

Creating a waypoint knowing a radial and DME to a navigation aid For this we need to enter a string with the following information: Location of the navigation aid (ICAO Code or Coordinates), radial and distance to the aid (in Nautical miles, Statute miles, Kilometers or meters)

Let's say I want to create a point that is on radial 275 of the VOR of Geneva (GVA) at 25NM DME I will have to enter the following string in the tool: GVA, R275, D25

The tool will choose the navigation aid with that name that is nearest to your actual position. Alternatively you can enter the coordinates:

46:15:12 N 06:08:14 E, R275, D25

If you want to use the true bearing instead of the radial you have to change the R for a B. An to change the unit just add SM for statute mile, KM for Kilometer or M for meter at the end of Distance:

GVA, B275, D25KM

Location, Direction, Speed, Time

Let 's say you are flying and you are requested by ATC to report your position 5 minutes after passing over GVA. You are flying at 108 knots GS and you are on the radial 275 of GVA.

You can enter this String and the tool will search for that point: GVA, R275, S108, T5

You can also enter a specific time in UTC. Use the Code AT before the time for this: GVA, R275, S108, AT12:58

You can also enter the speed in statute miles per hour, kilometers per hour and meters per second. Enter just MPH, KMH or MPS after the speed.

Location, Direction, Location, Direction

Creating a waypoint knowing the radials of two navigation aids You can create a point easily by entering the following information: Navigation Aid 1, Radial 1, Navigation Aid 2, Radial 2.

GVA, R100 , SCS, R300

Of course you can use coordinates or bearings for the above command.

98146.jpg


Search by geocoded places

caption

It is also possible to search by place names. By acquiring our Add-on Streets and places search you will be able to search for places like hotels, bars, hospitals and much more points of interest in the database. You can then use these points as regular waypoints by adding them to routes or showing them on the map.






Browse Database

caption

If you are not able to find the waypoint you are looking for, you can tap on "browse databade...". You can visualize quickly nearby waypoints or use the «search» tab to go search by country or search directly the waypoint you are looking for. It is possible to search by “name”, “ID” or “place”.

Once you found the desired waypoint, you can directly press on it to select it as a “direct to” or adjust it to one of the instruments (HSI, VOR, ADF); or you can press on the blue disclosure button on the right side and check the information about it such as name, city, frequency (for Navaids), runway and contact frequency info (for Airfields) and you can center the waypoint on the moving map by selecting «Show on map» button.

Showonmap.jpg


Create Waypoint via URL

In order to help the workflow it is possible to quickly insert waypoints in the application by tapping on a specially formatted URL. The URL can be sent by E-Mail, SMS or browsed on a website.

Supported actions:

  • Direct-to
  • Import waypoints to user database
  • Create route

The URL looks something like this: Clean: airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field Encoded query: airnavpro://direct-to?coordinates%3Dwgs84-decimal%26location%3D46.875_7.234%2C0.0%2CWP1%2CGrass%20field

It consists of:

  • URL scheme: airnavpro://
  • An action: direct-to
  • Coordinates format: coordinates=wgs84-decimal
  • waypoint(s): location=46.875_7.234,0.0,WP1,Grass field



Note: The query part of the URL has to be URL encoded in order to support special characters.



Coordinates formats:

  • wgs84-ddmmss
  • wgs84-decimal
  • wgs84-ddmmdecimal
  • utm-std
  • utm-band
  • ups
  • mgrs100
  • mgrs10
  • mgrs1
  • irish
  • ir+zone
  • nzgd1949
  • nzgd2000
  • swiss
  • uk
  • uk+zone
  • rt90
  • sweref99tm

Waypoint format For any action the waypoint can be defined with different values separated by a comma (,). Waypoints are separated by semicolons (;).

Waypoint values:

  1. Coordinates
  2. Elevation (in meters)
  3. Waypoint ID
  4. Waypoint name


A waypoint must at least contain the coordinates information. The coordinates information may be composed of two values, in this case the coordinates must be linked with a underscore (_). For example, a waypoint description for a wgs84 decimal format: 46.875_7.234

Here is a full example with elevation, ID and name data: 46.875_7.234,0.0,WP1, Antenna

Direct-to

Direct to can be achieved by formatting an URL with the "direct-to" command. Only one waypoint can be specified and it has to be in the form like :

location=waypoint

Here are some examples of direct-to URLs :

WGS84 decimal

 - airnavpro://direct-to?coordinates=wgs84-decimal&location=46.875_7.234,0.0,WP1,Grass field

WGS84 degrees minutes seconds

 - airnavpro://direct-to?coordinates=wgs84-ddmmss&location=N 12°34′56′′_W 78°12′34′′,0.0,WP1,Grass field

Swissgrid CH1903

 - airnavpro://direct-to?coordinates=swiss&location=602030.68_191775.03,0.0,WP1,Zimmerwald

Import waypoints to user database

A list of waypoints can be imported directly in the user database with a specially formatted URL with the "add-waypoints" command. A list of waypoints can be specified and it has to be in the form like :

waypoints=point1;point2;point3

Here is an example of add-waypoints URLs :

 - airnavpro://add-waypoints?coordinates=wgs84-decimal&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna

Create Route

A new route with a list of waypoints can be created and loaded directly with a specially formatted URL with the "new-route" command. A route name and list of waypoints can be specified and it has to have a form like: route-name=myRoute&waypoints=point1;point2;point3

Here is an example of add-waypoints URLs :

 - airnavpro://new-route?coordinates=wgs84-decimal&route-name=myRoute&waypoints=46.123_6.543,125.0,WP1,Grass field;47.113_7.143,225.1,WP2,Forrest;45.153_6.643,1225.0,WP3,Antenna


Back to index